Currencies:  

Open207Z-P-A STM32F207ZGT6 STM32F207 STM32 ARM + 10 Modules

$157.99

Qty Discounts Off Price
1-4
$157.99
5-9
$150.09
10+
$142.19
Always Free Shipping

This auction is for Open207Z Package A

 
STM32 development board designed for STM32F207Z series, features the STM32F207ZGT6 MCU, and integrates various standard interfaces, pretty easy for peripheral expan

STM32F207ZGT6: the STM32F2 Hi-Performance microcontroller which features:
Core: ARM Cortex-M3 32-bit RISC
Operating frequency: 120MHz, 150 DMIPS/1.25 DMIPS/MHz
Operating voltage: 1.8V-3.6V
Package: LQFP144
Memories: 1024KB Flash, 128+4kB SRAM
Communication interfaces:
3 x SPI, 3 x USART, 2 x UART,, 2 x I2S, 3 x I2C
1 x FSMC, 1 x SDIO, 2 x CAN
1 x USB 2.0 FS/HS device/host/OTG with on-chip PHY
1 x 10/100 Ethernet MAC
1 x 8 to 14-bit parallel camera interface
AD & DA converters: 3 x AD (12-bit, 1?s, shares 24 channels); 2 x DA (12-bit)
Debugging/Programming: supports JTAG/SWD (serial wire debug) interfaces, supports IAP
AMS1117-3.3: 3.3V voltage regulator
74LVC139: used for FSMC expansion, make it possible to connect multi devices through FSMC at the same time, such as LCD and NAND FLASH
Power supply switch: 5V DC or USB
Power indicator
LEDs: convenient for indicating I/O status and/or program running state
Reset button
User key: convenient for I/O input and/or interact with running code
Wake-Up button: wake up the STM32 MCU from sleep mode, also used as regular user key.
Joystick: convenient for I/O input (five positions)
32.768K crystal oscillator: for internal RTC, also supports clock calibration
25M crystal oscillator: enables the MCU run at 120M frequency by frequency multiplication
CAN1 interface: communicates with accessory boards which feature the CAN device conveniently
USART4 interface: easily connects to RS232, RS485, USB TO 232, etc.
DCMI interface: for connecting camera module
8 I/O interface: easily connects to keypad, motor, etc.
I2C3 interface: easily connects to I2C peripherals such as I/O expander (PCF8574), EEPROM (AT24Cxx), etc.
SPI3 interface: easily connects to SPI peripherals such as DataFlash (AT45DBxx), SD card, MP3 module, etc.
SPI1/SPI2 interface
easily connects to SPI peripherals such as DataFlash (AT45DBxx), SD card, MP3 module, etc.
SPI1 features AD/DA alternative function, supports connecting AD/DA module as well
I2C1/I2C2 interface: easily connects to I2C peripherals such as I/O expander (PCF8574), EEPROM (AT24Cxx), etc.
SDIO interface: for connecting Micro SD module, features much faster access speed rather than SPI
USART3 interface: easily connects to RS232, RS485, USB TO 232, etc.
USART5 interface: easily connects to RS232, RS485, USB TO 232, etc.
USART2 interface: easily connects to RS232, RS485, USB TO 232, etc.
CAN2 interface: communicates with accessory boards which feature the CAN device conveniently
FSMC interface (8-bit FSMC): easily connects to peripherals such as NandFlash, Ethernet, etc.
ONE-WIRE interface: easily connects to ONE-WIRE devices (TO-92 package), such as temperature sensor (DS18B20), electronic registration number (DS2401), etc.
FSMC (16-bit FSMC): for connecting peripherals such as NorFlash, SRAM, etc.
FSMC + SPI interface (16-bit FSMC + SPI): for connecting touch screen LCD
PS/2 interface: easily connects to PS/2 keyboard and/or mouse
USART1 interface: easily connects to RS232, RS485, USB TO 232, etc.
Ethernet interface: easily connects the MCU to ethernet network by using an additional ethernet module
USB: communicating with PC, and/or used as USB Host (requires an OTG cable)
5V DC jack
5V/3.3 V power input/output
MCU pins connector: all the MCU pins are accessible on expansion connectors for further expansion
JTAG/SWD interface: for debugging/programming
USB-VBUS jumper
short the jumper to enable STM32 USB detection
open the jumper to disable
USB OTG power output enable jumper
short the jumper to enable the USB-OTG provides power supply to external devices
open the jumper to disable
Boot mode selection: for configuring the BOOT0 and BOOT1 pins
LEDs jumper
short the jumper to connect the LEDs to default I/Os that used in example code
open the jumper to connect the LEDs to custom I/Os via jumper wires
User key/Joystick jumper
short the jumper to connect to default I/Os that used in example code
open the jumper to connect to custom I/Os via jumper wires
VREF selection jumper
short the jumper to connect VREF+ to VCC
open the jumper to customize VREF+
PS/2 interface jumper
short the jumper to connect the PS/2 device to default I/Os that used in example code
open the jumper to connect the PS/2 device to custom I/Os via jumper wires
74LVC139 selection jumper (used for FSMC chip selection)
short the jumper to connect to default I/Os that used in example code
open the jumper to connect to custom I/Os via jumper wires
VBAT selection jumper
short the jumper to use system power supply
open the jumper to make it possible to connect the VBAT to external power, such as battery


Note:
The Open207Z supports programming via STM32 USART bootloader, a USB TO UART accessory board is also provided in the package.
The Open207Z does NOT integrate any debugging function, a debugger is required.

Development Resources
The User Guide CD includes development resources listed as follow:

Related software (KEIL etc.)
Demo code (examples in C, ?C/OS-II)
Schematic (PDF)
STM32 development documentations (Datasheet etc.)

Standard Package
Open207Z development board x 1
PL2303 USB UART Board (mini) x 1
USB type A plug to mini-B plug cable x 1
4-pin wire x 2
2-pin wire x 2
5V Power Adapter x 1
User Guide CD x 1

Accessory Boards Package
3.2inch 320x240 Touch LCD (A) (FSMC + SPI) x 1
Analog Test Board (for AD/DA testing) x 1
SN65HVD230 CAN Board (CAN) x 1
DP83848 Ethernet Board x 1
FM24CLXX FRAM Board (I2C) x 1
Micro SD Storage Board (SDIO/SPI) x 1
K9F1G08U0C NandFlash Board (FSMC)
S29GL128P NorFlash Board (FSMC)
IS62WV12816BLL SRAM Board (FSMC)
OV7670 Camera Board (DCMI)



Add to Cart:

  • Model: SH460500
  • Shipping Weight: 70 gram