Currencies:  

Port407V STM32F407VGT6 STM32F407 STM32 ARM Cortex-M4 Core Develo

$39.50

Qty Discounts Off Price
1-4
$39.50
5-9
$37.53
10+
$35.55
Always Free Shipping

 Port407V STM32F407VGT6 STM32F407 STM32 ARM Cortex-M4 Core Development Board Kit

Port407V is an STM32 development board that features an STM32F407VGT6 device as the microcontroller, supports further expansion with various optional accessory boards for your specific application. It is ideal for starting application development with STM32F family.

Note: Optional accessory boards are NOT included in the price.

STM32F407VGT6: the high performance STM32 MCU which features:
Core: Cortex-M4 32-bit RISC
Feature: a full set of single-cycle DSP instructions
Operating Frequency: 168MHz, 210 DMIPS/1.25 DMIPS/MHz
Operating Voltage: 1.8V-3.6V
Package: LQFP100
Memories: 1024kB Flash, 192+4kB SRAM
Communication Interfaces:
3 x SPI, 3 x USART, 2 x UART, 2 x I2S, 3 x I2C
1 x FSMC, 1 x SDIO, 2 x CAN
1 x USB 2.0 FS/HS device/host/OTG with on-chip PHY
1 x 10/100 Ethernet MAC
1 x 8 to 12-bit parallel camera interface
AD & DA converters: 3 x AD (12-bit, 1?s, shares 24 channels); 2 x DA (12-bit)
Debugging/Programming: supports JTAG/SWD (serial wire debug) interfaces, supports IAP
AMS1117-3.3: 3.3V voltage regulator
Power indicator
LEDs: convenient for indicating I/O status or program debugging running state
Reset button
User keys
Joystick: five positions
25M crystal oscillator
32.768K crystal, used for internal RTC, also supports clock calibration
JTAG/SWD interface: for debugging/programming
USB connector, used for establishing USB communication between PC and the STM32 development board
USART1 connector, supports ISP (In-System Programming) through USART1, as well as system signal output
IO expander, all the MCU pins are accessible on expansion connectors for further expansion
Power input/output header, 5V/3.3V, usually used for power output, or common ground with other user board
5V DC power jack
Boot mode selection: for configuring the BOOT0 and BOOT1 pins
Power supply switch, powered from 5V DC jack or USB connection
OTG PWR OUT enable jumper
short the jumper to enable OTG PWR OUT
open the jumper to disable, as well as taking up no I/O port
OTG VBUS enable jumper
short the jumper to enable OTG VBUS
open the jumper to disable, as well as taking up no I/O port
VBAT selection jumper
short the jumper to use system power supply
open the jumper to connect the VBAT to external power, such as battery
VREF jumper
short the jumper to connect VREF+/VREF- respectively to VCC/GND
open the jumper to connect VREF+/VREF- to other custom pins via jumper wires
User LEDs jumper
short the jumper to connect to I/Os that used in example code
open the jumper to connect to other custom pins via jumper wires
User keys jumper
short the jumper to connect to I/Os that used in example code
open the jumper to connect to other custom pins via jumper wires
Joystick jumper
short the jumper to connect to I/Os that used in example code
open the jumper to connect to other custom pins via jumper wires


Note:
Accessory board and programmer/debugger in the photos are NOT included in the price.
Port407V supports programming through USART port without programmer.
Port407V provides JTAG/SWD debugging interface, yet does NOT integrate any debugging function, a debugger is required.

 
JTAG/SWD Interfaces
The figure 1, figure 2 shows the header pinout of JTAG, SWD interface respectively

Development Resources
Port407V development board comes with a User Guide CD including development resources listed as below:

Related software (KEIL etc.)
Examples in C
Schematic (PDF)
Development documentations


Package Contains
Port407V development board x 1
USB type A to Mini-B cable x 1
USB power cable x 1
4-pin wire x 2
2-pin wire x 2
User guide CD x 1



Add to Cart:

  • Model: SH460494
  • Shipping Weight: 70 gram